JumboSPOT official website: how to upgrade fw

2018年1月3日星期三

how to upgrade fw

download putty ssh login pi-star's ip:22
user:pi-star
pass:raspberry

copy follow pre line and press enter to run the command in putty terminal
----------------------------------------------------------------------------------------
rpi-rw
sudo service mmdvmhost stop
sudo pkill MMDVMHost
cd /tmp
sudo rm MMDVM_HS-1.3.3.bin
sudo wget http://www.taozhengbo.com/MMDVM_HS-1.3.3.bin
sudo chmod 664 MMDVM_HS-1.3.3.bin
sleep 2
sudo pkill MMDVMHost
sudo pkill mmdvmhost.service
sudo stm32flash -v -w MMDVM_HS-1.3.3.bin -g 0x0 -R -i 20,-21,21:-20,21 /dev/ttyAMA0
echo "Rebooting Pi"
sleep 30
sudo reboot
--------------------------------------------------------------------------------------
Video:

https://www.youtube.com/watch?v=gwKgOiBcSxQ&feature=youtu.be

11 則留言:

Unknown2018年1月12日上午8:35
pi-star@h-pi-star(rw):scripts$ ./install_fw_rpi.sh
% Total % Received % Xferd Average Speed Time Time Time Current
Dload Upload Total Spent Left Speed
100 608 0 608 0 0 298 0 --:--:-- 0:00:02 --:--:-- 299
100 49752 100 49752 0 0 8690 0 0:00:05 0:00:05 --:--:-- 22916
Raspberry Pi 2 or Pi Zero W detected
stm32flash Arduino_STM32_0.9

http://github.com/rogerclarkmelbourne/arduino_stm32

Using Parser : Raw BINARY
Interface serial_posix: 57600 8E1
Failed to init device.

please help.
回覆刪除
回覆
Unknown2018年1月14日上午11:13
I got the same error! "Failed to init device".
回覆刪除
回覆
buy insanity workout2018年1月16日晚上7:08
you must kill MMDVMHost
ps -ef see MMDVMHost 's pid
then kill pid of MMDVMHost
then run ./install_fw_rpi.sh
回覆刪除
回覆
Unknown2018年1月16日晚上8:22
I connect the two pin and my micro sd card broken :(
why?
回覆刪除
回覆
buy insanity workout2018年1月18日晚上7:43
it is for raspberry pi gpio control RESET MCU and BOOT0 to upgrade mode,so don't nned to cancel link,the easy way only connect 2 last pin to raspberry not short.raspberry control one pin to reset mcu,another pin to boot0 high or low to boot loader mode.

another upgrade method is to use st-link ,board have stlink 4 hold ,GND ,CLK,DIO,3V3 to connect stlink upgrade use STM32 ST-LINK Utility,open .bin file to upgrade.
回覆刪除
回覆
Clinton2018年2月13日下午3:19
Where do I find install_fw_rpi.sh?
回覆刪除
回覆
Unknown2018年2月18日下午2:21
Hello,

I own a JumboSpot RTQ.
How do I know which firmware revision is currently running on the board?

Thank you.

Regards,
Simone IU3KHJ
回覆刪除
回覆
Keith2018年5月31日上午10:26
What method is used to update mmdvm-pi repeater board?
回覆刪除
回覆