tag:blogger.com,1999:blog-919648345316809012.post9017679723266914495..comments2022-04-10T17:08:19.152-07:00Comments on JumboSPOT official website: how to upgrade fwUnknownnoreply@blogger.comBlogger11125tag:blogger.com,1999:blog-919648345316809012.post-63381700256763137432018-05-31T10:26:20.763-07:002018-05-31T10:26:20.763-07:00What method is used to update mmdvm-pi repeater bo...What method is used to update mmdvm-pi repeater board?<br />Keithhttps://www.blogger.com/profile/15462054931096081272noreply@blogger.comtag:blogger.com,1999:blog-919648345316809012.post-19494962179529809332018-03-02T19:38:05.350-08:002018-03-02T19:38:05.350-08:00copy script and save to install_fw_rpi.shcopy script and save to install_fw_rpi.shbuy insanity workouthttps://www.blogger.com/profile/00707463592750515701noreply@blogger.comtag:blogger.com,1999:blog-919648345316809012.post-1030797531672476432018-03-02T19:37:10.292-08:002018-03-02T19:37:10.292-08:00you can find in pi-star panel RADIO INFO FWyou can find in pi-star panel RADIO INFO FWbuy insanity workouthttps://www.blogger.com/profile/00707463592750515701noreply@blogger.comtag:blogger.com,1999:blog-919648345316809012.post-56638133075700623442018-02-18T14:21:07.938-08:002018-02-18T14:21:07.938-08:00Hello,
I own a JumboSpot RTQ.
How do I know which...Hello,<br /><br />I own a JumboSpot RTQ.<br />How do I know which firmware revision is currently running on the board?<br /><br />Thank you.<br /><br />Regards,<br />Simone IU3KHJ Anonymoushttps://www.blogger.com/profile/08466111250928425681noreply@blogger.comtag:blogger.com,1999:blog-919648345316809012.post-69753467593284045342018-02-13T15:19:51.350-08:002018-02-13T15:19:51.350-08:00Where do I find install_fw_rpi.sh?Where do I find install_fw_rpi.sh?Clintonhttps://www.blogger.com/profile/02747557554868553589noreply@blogger.comtag:blogger.com,1999:blog-919648345316809012.post-71163216097552575052018-01-18T19:43:14.589-08:002018-01-18T19:43:14.589-08:00it is for raspberry pi gpio control RESET MCU and ...it is for raspberry pi gpio control RESET MCU and BOOT0 to upgrade mode,so don't nned to cancel link,the easy way only connect 2 last pin to raspberry not short.raspberry control one pin to reset mcu,another pin to boot0 high or low to boot loader mode.<br /><br />another upgrade method is to use st-link ,board have stlink 4 hold ,GND ,CLK,DIO,3V3 to connect stlink upgrade use STM32 ST-LINK Utility,open .bin file to upgrade.buy insanity workouthttps://www.blogger.com/profile/00707463592750515701noreply@blogger.comtag:blogger.com,1999:blog-919648345316809012.post-59276911669215264472018-01-16T20:22:54.125-08:002018-01-16T20:22:54.125-08:00I connect the two pin and my micro sd card broken ...I connect the two pin and my micro sd card broken :(<br />why?Anonymoushttps://www.blogger.com/profile/17357123792989428016noreply@blogger.comtag:blogger.com,1999:blog-919648345316809012.post-47723518289625293762018-01-16T19:25:49.562-08:002018-01-16T19:25:49.562-08:00can i use iron wire link two pin ?
Need to cancel ...can i use iron wire link two pin ?<br />Need to cancel the link after the upgrade?Anonymoushttps://www.blogger.com/profile/17357123792989428016noreply@blogger.comtag:blogger.com,1999:blog-919648345316809012.post-29485589021693141002018-01-16T19:08:16.420-08:002018-01-16T19:08:16.420-08:00you must kill MMDVMHost
ps -ef see MMDVMHost '...you must kill MMDVMHost<br />ps -ef see MMDVMHost 's pid<br />then kill pid of MMDVMHost<br />then run ./install_fw_rpi.shbuy insanity workouthttps://www.blogger.com/profile/00707463592750515701noreply@blogger.comtag:blogger.com,1999:blog-919648345316809012.post-71290634725567875512018-01-14T11:13:05.619-08:002018-01-14T11:13:05.619-08:00I got the same error! "Failed to init devic...I got the same error! "Failed to init device".<br />Anonymoushttps://www.blogger.com/profile/01584442084397765533noreply@blogger.comtag:blogger.com,1999:blog-919648345316809012.post-28287536196283549152018-01-12T08:35:27.545-08:002018-01-12T08:35:27.545-08:00pi-star@h-pi-star(rw):scripts$ ./install_fw_rpi.sh...pi-star@h-pi-star(rw):scripts$ ./install_fw_rpi.sh <br /> % Total % Received % Xferd Average Speed Time Time Time Current<br /> Dload Upload Total Spent Left Speed<br />100 608 0 608 0 0 298 0 --:--:-- 0:00:02 --:--:-- 299<br />100 49752 100 49752 0 0 8690 0 0:00:05 0:00:05 --:--:-- 22916<br />Raspberry Pi 2 or Pi Zero W detected<br />stm32flash Arduino_STM32_0.9<br /><br />http://github.com/rogerclarkmelbourne/arduino_stm32<br /><br />Using Parser : Raw BINARY<br />Interface serial_posix: 57600 8E1<br />Failed to init device.<br /><br />please help.Anonymoushttps://www.blogger.com/profile/17357123792989428016noreply@blogger.com